Any alteration or modification not specified is misuse and may result in dangerous conditions. Damaged cords increase the risk of electric shock. Keep cord away from heat, oil, sharp edges or moving parts. Never use the cord to carry the tools or pull the plug from an outlet. Be aware of switch location and know how to shut off the tool in emergency situations. Never leave the switch in the “ON” position. Be aware of the location and setting of the switch “ON" position. Don’t leave tool until it comes to a complete stop. It’s safer than using your hand and it frees both hands to operate the tool.įeed work into a blade or cutter against the direction of rotation of the blade or cutter only. Don’t use tool for purpose not intended - for example don’t use circular saw for cutting tree limbs or logs. It will do the job better and safer at the rate for which it was designed.ĭon’t force small tool or attachment to do the job of a heavyduty tool. THE USE OF ANY OTHER ACCESSORIES NOT SPECIFIED IN THE CURRENT SKIL CATALOG MAY CREATE A HAzARD. A guard or other part that is damaged should be properly replaced.ĪLL REPAIRS, ELECTRICAL OR MECHANICAL, SHOULD bE ATTEMPTED ONLY bY TRAINED REPAIRMEN.Ĭontact the nearest Skil Factory Service Center, Authorized Service Station or other competent repair service. Check for alignment of moving parts, mounting and any other conditions that may affect its operation. Do not store materials on or near the tool such that it is necessary to stand on the tool or its stand to reach them.īefore further use of the tool, a guard or other part that is damaged should be carefully checked to ensure that it will operate properly and perform its intended function. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Make sure the switch is in the “OFF” (“O”) position before plugging in tool. In working order, and in proper adjustment and alignment. When not in use, before servicing, when changing blades, bits, cutters, etc. For example: pipes, radiators, ranges, refrigerator enclosures. Prevent body contact with grounded surfaces. Also, use face or dust mask if cutting operation is dusty, and ear protectors (plugs or muffs) during extended periods of operation. Wear non-slip footwear and a hard hat, if appropriate. Wear safety goggles (must comply with ANSI Standard Z87.1) at all times. Rubber gloves and non-skid footwear are recommended when working outdoors. Tie back long hair or wear protective hair covering and roll long sleeves above the elbow. To avoid being pulled into a blade, do not wear loose clothing, loose fitting gloves, necktie or jewelry. Do not operate while under medication or while using alcohol or other drug. Keep proper footing and balance at all times. SKIL X-BENCH 3100 This has turned out much better than I had anticipated. Learn its application and limitations as well as the specific potential hazards peculiar to this tool. Read and understand the owner’s manual and labels affixed to the tool. Do not use tool in presence of flammable liquids or gases. Skil 3110 XBench Portable Work Station Parts We Sell Only Genuine Skil Parts Popular Parts Supporting Foot / 25 4.19 Add to Cart Search within model Questions & Answers Page A Hotspots Fig 21 Clamp Part Number:3860180011 Ships in 12 - 18 business days 4. All visitors should be kept away from work area.Ĭluttered areas and benches invite accidents.ĭon’t use power tools in damp or wet locations. Is $150 a fair price for the XBench? I'm not sure, but I'd probably buy it again if I were in the same situation.Do not let visitors contact tool or extension cord. You could make something similar, but it would take a lot of effort to duplicate the way this table folds up and the way the top slides to the side to open up the center channel. I tried it once, and common sense made me turn the saw off after about 10 seconds. Oh, I also bought the jigsaw mounting plate. The "wedge dogs" that come with the clamping kit are great for this. That said, the center channel is pretty great, especially for making rough crosscuts with a circular saw or jigsaw. I haven't tried, but I imagine that the angular stresses would be too much. The MDF seems too thin in spots to use holdfasts or normal bench dogs. Although it feels pretty heavy when you're moving around, it's not nearly heavy enough for using hand tools. It's not a bad table if you understand the limitations: I also bought the clamping kit and the end vise. I bought one when my workshop was one half of the garage, and I needed to be able to pack everything away to get a car in there.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |